CIM 500 – Durable Waterproofing Membrane
CIM 500 is a tough, durable membrane specifically formulated to meet waterproofing demands in a buried and non-UV exposed application.
It adheres to most materials to form a permanent, seamless barrier to water.
It is well suited for plaza and podium decks, curbs, and areas containing multiple penetrations or irregular shapes, as well as split-slab applications.
Available in both a vertical and horizontal grade.
 |
 |
| CIM 500 Premix | CIM 500V Premix for Vertical Surfaces |
- tough, durable physical properties
- forms strong adhesive bond to concrete, wood, metal, and earth (with scrim fabric)
- applied by spray, brush, roller, or squeegee
- fast cure, high tensile strength, low VOC
- lower water permeability than competitive urethanes
- open to foot traffic within 3 hours
- UV stable for as long as 180 days
- little to no sloping is required
- chemically stable when subjected to constant moisture
- can be applied in low-temperature applications
- simple repair to existing installations
- planter boxes
- plaza and podium decks
- green roof applications
- split-slab applications
- below-grade applications
- apply by spray, brush, roller, or squeegee.
- apply to clean, dry, & sound surfaces free of dirt and debris.
- can be applied to concrete substrates having a (CSP 4-6) surface profile.
- mix and apply the following CIM industries .
- use CIM 500V on all vertical surfaces and use CIM 500 on all horizontal surfaces
SPECIFICATION & SIZES
| Property | Value |
| Thickness | 60 wet mils minimum |
| Bond strength | 350 psi to concrete |
| Permeability | .03 perms |
| Elongation | 200 % |
| Tensile Strength | 700psi |
PACKAGING INFORMATION
- 5-gallon units
- Activator ½ gallon Jug (.45 gallons of material)
- Packaged 6 jugs per box
For CIM 500, thin-set and tile, pedestal paver systems, decorative aggregate.
CIM 500 is UV stable for 180 days.
Typically, CIM 500 can be placed in service within 24-48 hours. Contact C.I.M. Industries for specific recommendations.
Surface should be at least 50°F (10°C) and must be 5°F (3°C) above the dew point. CIM 500 should be at least 50°F (10°C) when mixed and applied. CIM 500 may be preheated to facilitate application at low temperatures, but working time will be reduced.
- Advantages & Benefits
-
- tough, durable physical properties
- forms strong adhesive bond to concrete, wood, metal, and earth (with scrim fabric)
- applied by spray, brush, roller, or squeegee
- fast cure, high tensile strength, low VOC
- lower water permeability than competitive urethanes
- open to foot traffic within 3 hours
- UV stable for as long as 180 days
- little to no sloping is required
- chemically stable when subjected to constant moisture
- can be applied in low-temperature applications
- simple repair to existing installations
- Where to Use It
-
- planter boxes
- plaza and podium decks
- green roof applications
- split-slab applications
- below-grade applications
- How to Use it
-
- apply by spray, brush, roller, or squeegee.
- apply to clean, dry, & sound surfaces free of dirt and debris.
- can be applied to concrete substrates having a (CSP 4-6) surface profile.
- mix and apply the following CIM industries .
- use CIM 500V on all vertical surfaces and use CIM 500 on all horizontal surfaces
- Specification & Sizes
-
SPECIFICATION & SIZES
Property Value Thickness 60 wet mils minimum Bond strength 350 psi to concrete Permeability .03 perms Elongation 200 % Tensile Strength 700psi PACKAGING INFORMATION
- 5-gallon units
- Activator ½ gallon Jug (.45 gallons of material)
- Packaged 6 jugs per box
- Frequently Asked Question
-
What architectural finishes are compatible?
For CIM 500, thin-set and tile, pedestal paver systems, decorative aggregate.
What are environmental concerns for cold fluid applied vs sheet membranes ?CIM 500 is UV stable for 180 days.
What is the cure/in-service time for cold fluid applied?Typically, CIM 500 can be placed in service within 24-48 hours. Contact C.I.M. Industries for specific recommendations.
What is the application temperature range for cold fluid applied?Surface should be at least 50°F (10°C) and must be 5°F (3°C) above the dew point. CIM 500 should be at least 50°F (10°C) when mixed and applied. CIM 500 may be preheated to facilitate application at low temperatures, but working time will be reduced.
- How to Videos
-
Supplemental Products
 |
 |
 |
 |
| CIM Primers | 4EvaSeal Fabric Backed Tape | CIM 1000 TG | CIM Scrim |
Need more information?Â
Product Approval
 |
|
Let’s connect and never miss an update or news from us.
If you have already registered, please login to view SDS files.
